Drill chucks

KEY TYPE DRILL CHUCKS
TYPE : H , XH

	Suitable for use on heavy duty & extra heavy duty.
	For milling machine, lathe, drill machine & wood working machine.

Type	Clamping Capacity	Female Taper DIN or Jacobs	Female Thresd Inch or metic
4H	0.5-4(mm) ; 1/64"-5/32" (inch)	J0
5H	0.5-5	5D
5HB	0.5-6	5D
6H	0.5-6.5(mm) ; 1/64"-1/4" (inch)	J1 B10 Ø 5.5X90^o	3/8-24
10H	1-10(mm) ; 1/32"-3/8" (inch)	J2S ;J6 ;B16 ; B18 ;J1 Ø 5.5X90^o Ø 6.5X90^o	3/8-24 1/2-20
13H	1-13(mm) ; 1/32"-1/2"" (inch)	J2S ; J6 ; B16; B18 Ø 5.5X90^o Ø 6.5X90^o	3/8-24 1/2-20
16H	1-16(mm) ; 1/32"-5/8" (inch)	J6 ; J3 ; B16 ; B18 Ø 5.5X90^o Ø X90^o	1/2-20 5/8-16
19H	3-19(mm) ; 1/8"-3/4" (inch)	B22 J3
13XH	1-13(mm) ; 1/32"-1/2" (inch)	Ø 6.5X90^o J6 ; B16 ; J33	1/2-20
19XH	1-19(mm) ; 1/32"-3/4" (inch)	J4 ; B22

Material Analysis Table
Parts No.	Parts Name	Material	Heat-Treatment
1	Body	JIS G4051 SAE 1045	HRC45-48
2	Case	JIS 4018 SAE 1018	HRC38-40
3	Jaws	JIS SUJ2 SAE 52100	HRC52 ± 2
4	Nut	JIS 4051 SAE 1045	HRC61 ± 2

Run-out Accuracy & Torsion Inspection Table

Type	4H	5H	6.5H	10H	13H	16H	19H	13XH	19XH
Ø dmm	3.5	4.5	6	9	12	15	18	12	18
L mm	60	80	90	110	140	150	150	140	150
L1 mm	40	60	70	85	110	120	120	110	120
Max Run-out mm	0.15	0.15	0.15	0.15	0.15	0.15	0.15	0.15	0.15
Torque kgf-cm	18	20	45	75	85	250	300	190	300

KEY TYPE DRILL CHUCK
TYPE : M

	Suitable for general electric drill, pneumatic drill, impact electric drill, light weight.
	Key hole hardened by high frequency heat treatment, long service life.

Type	Clamping Capacity	Female Taper DIN or Jacobs
10M	1-10(mm) ; 1/32"-3/8"" (inch)	Ø 5.5X90^o Ø 6.5X90^o
13M	1.5-13(mm) ; 3/64-1/2" (inch)	Ø 6.5X90^o Ø 5.5X90^o

Material Analysis Table
Parts No.	Parts Name	Material	Heat-Treatment
1	Body	JIS G4051 SAE 1045	HRC45-48
2	Case	JIS 4018 SAE 1045
3	Jaws	JIS 4051 SAE 1045	HRC52 ± 2
4	Nut	JIS 4051 SAE 1045	HRC61 ± 2

Run-out Accuracy & Torsion Inspection Table

Type	Ø dmm	L1 mm	Max mm	Torque kgf-cm
10M	9	85	0.20	70
13M	12	110	0.20	70

BACK

NEXT